SMC EliteConnect Wireless Bridge Uživatelská příručka Strana 255
- Strana / 318
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Wireless Interface Commands
7-107
7
rts-threshold
This command sets the packet size threshold at which a Request to Send (RTS)
signal must be sent to the receiving station prior to the sending station starting
communications.
Syntax
rts-threshold <threshold>
threshold - Threshold packet size for which to send an RTS.
(Range: 0-2347 bytes)
Default Setting
2347
Command Mode
Interface Configuration (Wireless)
Command Usage
• If the threshold is set to 0, the access point always sends RTS signals. If set
to 2347, the access point never sends RTS signals. If set to any other value,
and the packet size equals or exceeds the RTS threshold, the RTS/CTS
(Request to Send / Clear to Send) mechanism will be enabled.
• The access point sends RTS frames to a receiving station to negotiate the
sending of a data frame. After receiving an RTS frame, the station sends a
CTS frame to notify the sending station that it can start sending data.
• Access points contending for the wireless medium may not be aware of
each other. The RTS/CTS mechanism can solve this “Hidden Node”
problem.
Example
SMC AP(if-wireless g)#rts-threshold 256
SMC AP(if-wireless g)#
- USER GUIDE 1
- Copyright 3
- Compliances 4
- VCCI Notice 5
- EC Conformance Declaration 5
- Community 5
- Safety Compliance 7
- Power Cord Set 8
- (Germany): 10
- <BASEC> tragen 11
- Table of Contents 12
- Chapter 1: Introduction 20
- Package Checklist 21
- Hardware Description 21
- LED Indicators 22
- Introduction 23
- Ethernet Port 24
- Power Injector Module 24
- Grounding Point 25
- Water Tight Test Point 25
- Features and Benefits 26
- Access Point Topologies 27
- Infrastructure Wireless LAN 28
- Point-to-Point Configuration 30
- Bridge Link Topologies 31
- Network Configuration 32
- Data Rates 33
- Radio Path Planning 33
- Antenna Height 34
- Bridge Link Planning 36
- Radio Interference 37
- Weather Conditions 37
- Grounding 38
- Testing Basic Link Operation 39
- Mount the Unit 39
- Mounting on a Pole 40
- Mounting to a Wall 42
- Connect External Antennas 43
- Connect Cables to the Unit 44
- Ground Wire 45
- Ethernet Cable 45
- Grounding Screw 45
- Align Antennas 46
- Hardware Installation 48
- Required Connections 49
- Initial Configuration Steps 50
- Logging In 51
- Initial Configuration 52
- Advanced Configuration 54
- System Identification 55
- TCP / IP Settings 57
- SSH Settings 63
- Authentication 64
- Filter Control 69
- WDS Settings 73
- AP Management 79
- Administration 80
- Upgrading Firmware 81
- System Log 85
- Configuring SNTP 87
- Configuring SNMPv3 Users 98
- System Configuration 100
- Configuring SNMPv3 Targets 102
- Radio Interface 103
- Radio Settings A (802.11a) 105
- Normal Mode 111
- Turbo Mode 111
- Configuring Wi-Fi Multimedia 114
- Radio Settings G (802.11g) 120
- Security 122
- Enabling the VAPs 127
- Wi-Fi Protected Access (WPA) 133
- Configuring 802.1X 138
- Status Information 140
- Station Status 143
- Event Logs 145
- STP Status 147
- Chapter 7: Co 149
- Entering Commands 150
- Command Completion 151
- Getting Help on Commands 151
- Showing Commands 151
- SMC AP#show s? 152
- SMC AP#show s 152
- Exec Commands 153
- Configuration Commands 153
- Command Groups 154
- General Commands 155
- Command Line Interface 156
- System Management Commands 159
- APmgmtIP 169
- APmgmtUI 170
- System Logging Commands 177
- System Clock Commands 182
- DHCP Relay Commands 187
- SNMP Commands 189
- Flash/File Commands 204
- RADIUS Client 208
- 802.1X Authentication 214
- 802.1x session-timeout 216
- 802.1x-supplicant enable 217
- 802.1x-supplicant user 217
- MAC Address Authentication 219
- Filtering Commands 222
- WDS Bridge Commands 226
- Spanning Tree Commands 233
- Ethernet Interface Commands 238
- Wireless Interface Commands 243
- Rogue AP Detection Commands 264
- Wireless Security Commands 268
- Link Integrity Commands 278
- IAPP Commands 282
- VLAN Commands 283
- WMM Commands 285
- Appendix A: Troubleshooting 289
- Troubleshooting 290
- 10/100BASE-TX Pin Assignments 291
- Straight-Through Wiring 292
- Crossover Wiring 293
- 8-Pin DIN Connector Pinout 293
- Cables and Pinouts 294
- General Specifications 295
- Specifications 296
- Sensitivity 298
- Transmit Power 299
- V-förmige Halterung 301
- Montieren der Bridge 302
- Ethernet-Kabel 307
- Erdungsleitung 307
- Glossary 309
- Model Number: SMC2890W-AG / 317
- SMC2891W-AG 317
- Pub. Number: 149100034900E 317
- SMC2890W-AG / 318
Pelco BU5 650 manuales
Manuales del propietario y guías del usuario para Sistemas De Videovigilancia Pelco BU5 650.
Ofrecemos 1 manuales en pdf Pelco BU5 650 para descargar gratis por tipos de documentos: Manual de usuario
Komentáře k této Příručce